Record Raven PS3 Eye driver bring-up
This commit is contained in:
parent
62323ae508
commit
03cd8e4b1f
3 changed files with 42 additions and 5 deletions
|
|
@ -425,3 +425,35 @@ Conclusion: the split-host local set is viable when the Focusrite is not on the
|
|||
Leap's USB neighborhood. Full-height Leap stereo is still a little below the
|
||||
old ~110.8 fps best result, but the catastrophic ~81 fps band was caused by the
|
||||
local USB layout, not by needing every camera off the machine.
|
||||
|
||||
## 2026-05-21: Raven PS3 Eye Driver Bring-Up
|
||||
|
||||
Raven initially enumerated the PS3 Eye composite and media interfaces, but the
|
||||
raw `VID_1415&PID_2000&MI_00` camera interface had no driver binding and showed
|
||||
`Error`.
|
||||
|
||||
The working Mimir host binding was exported and installed on Raven:
|
||||
|
||||
- provider: `libwdi`;
|
||||
- service: `WinUSB`;
|
||||
- local source INF: `oem26.inf`;
|
||||
- Raven published INF: `oem34.inf`;
|
||||
- device interface GUID from the INF: `{6ACBF2FC-1246-418C-A63D-0FE38B45129B}`.
|
||||
|
||||
The libwdi self-signed catalog certificate had to be copied to Raven and added
|
||||
to both `Root` and `TrustedPublisher` before `pnputil /add-driver ... /install`
|
||||
would accept the package.
|
||||
|
||||
After binding, Raven's raw Eye interface reported `OK` and the copied
|
||||
`ps3eye_dual_cadence.exe` could open the camera. Cadence is not yet viable:
|
||||
|
||||
| Raven PS3 Eye Mode | Delivered FPS | Notes |
|
||||
| --- | ---: | --- |
|
||||
| 320x240@187 | 132.24 | first run, max gap 202.841 ms |
|
||||
| 320x240@187 | 78.93 | second run, max gap 283.247 ms |
|
||||
| 640x480@60 | 6.32 | max gap 2998.965 ms |
|
||||
|
||||
Conclusion: Raven's PS3 Eye driver binding is fixed enough to open the device,
|
||||
but the current Raven USB path/device state is not delivering usable cadence.
|
||||
Next Raven work is port/controller isolation and a clean single-process cadence
|
||||
run before treating the Eye as a usable remote timing witness.
|
||||
|
|
|
|||
|
|
@ -18,3 +18,4 @@
|
|||
{"ts":"2026-05-22T01:10:00+00:00","type":"verification","status":"partial","note":"Port isolation follow-up put Leap alone on the blue rear USB3 group/root_hub30#5 port 3, Kiyos together on root_hub30#7&18eea21b, and Eyes on remaining front/back USB-A ports. Only one PS3 Eye enumerated. Visible simultaneous pull with PS3 Eye at 320x240@187 delivered Leap stereo 80.99 fps, Kiyo Pro 24.93 fps, Kiyo 30.37 fps, and PS3 Eye 185.85 fps. Leap did not recover to its solo ~110 fps cadence despite root-hub isolation, so the bottleneck is not only same-row/same-root-hub contention; investigate broader xHCI scheduling, CPU/interrupt pressure, or KS/usbvideo behavior under multi-device load."}
|
||||
{"ts":"2026-05-22T01:30:00+00:00","type":"verification","status":"partial","note":"After splitting cameras across Mimir and Raven, the local Mimir host enumerated LeapUVC, regular Kiyo, and one PS3 Eye. Local simultaneous pull with PS3 Eye 320x240@187 delivered Leap 81.34 fps, Kiyo 30.27 fps, and PS3 Eye 185.56 fps. Leap+Kiyo only delivered Leap 82.77 fps and Kiyo 16.83 fps. Leap-only same-session baseline delivered 84.18 fps, with best fast-combined scenario 92.87 fps and 640x120 baseline 173.62 fps. Offloading Kiyo Pro and one PS3 Eye did not restore the previous ~110.8 fps Leap result; current hypothesis shifts to Leap port/controller/device state or KS/usbvideo behavior, not only total local camera bandwidth."}
|
||||
{"ts":"2026-05-22T01:45:00+00:00","type":"verification","status":"ok","note":"Moving the Focusrite Scarlett Solo away from the Leap USB neighborhood substantially recovered local split-host cadence. Leap-only baseline rose to 95.48 fps, best fast-combined scenario to 101.67 fps, and 640x120 baseline to 192.83 fps. With local Leap + regular Kiyo + one PS3 Eye at 320x240@187 active, Leap delivered 105.10 fps, Kiyo 30.17 fps, and PS3 Eye 185.81 fps. The split-host local set is viable; the prior ~81 fps Leap band was caused by local USB layout including the Focusrite, not just camera count."}
|
||||
{"ts":"2026-05-22T02:05:00+00:00","type":"verification","status":"partial","note":"Raven PS3 Eye raw interface initially had no driver binding. Exported the working Mimir host libwdi WinUSB driver package from oem26.inf, copied it to Raven under C:\\Meta\\mimir-ps3eye-winusb-driver, added the libwdi self-signed certificate to Raven Root and TrustedPublisher stores, and installed it as oem34.inf with pnputil. Raven now reports VID_1415&PID_2000&MI_00 as USBDevice OK, provider libwdi, service WinUSB. The copied ps3eye_dual_cadence.exe opens the device, but cadence is not viable yet: 320x240@187 delivered 132.24 fps then 78.93 fps, and 640x480@60 delivered 6.32 fps with multi-second gaps. Driver open is solved; Raven USB path/device cadence still needs isolation."}
|
||||
|
|
|
|||
|
|
@ -126,10 +126,14 @@ current_status:
|
|||
95.48 fps, best full-height scenario to 101.67 fps, and the local split set
|
||||
delivered Leap 105.10 fps, regular Kiyo 30.17 fps, and one PS3 Eye 185.81
|
||||
fps. The split-host layout is viable if the Leap's USB neighborhood stays
|
||||
free of the Focusrite and other heavy devices.
|
||||
free of the Focusrite and other heavy devices. Raven's PS3 Eye raw interface
|
||||
now has the same libwdi WinUSB binding as the local Eye and can be opened by
|
||||
the copied cadence probe, but Raven Eye cadence is currently unusable:
|
||||
320x240@187 delivered 132.24 fps then 78.93 fps, and 640x480@60 delivered
|
||||
6.32 fps with multi-second gaps.
|
||||
next_action: >
|
||||
Move the raw PS3 Eye probe into the repo or replace it with the first
|
||||
runtime capture driver, then rerun the six-optical-sensor pull from repo
|
||||
probes after deliberate USB topology changes. Keep high-rate cameras split
|
||||
across controllers/hubs deliberately, because current shared-load tests show
|
||||
Leap is no longer a stable timing authority under the present USB topology.
|
||||
runtime capture driver, then isolate Raven's PS3 Eye port/controller until
|
||||
its raw WinUSB cadence is stable. Keep high-rate cameras split across
|
||||
controllers/hubs deliberately, because current shared-load tests show Leap
|
||||
and the Eyes are sensitive to non-camera USB neighbors.
|
||||
|
|
|
|||
Loading…
Reference in a new issue